Reman Duramax 6.6 Long Block LBZ/LMM Engine W/ ARP Head Studs

Description: XCALIBUR DIESEL PERFORMANCE AND XCALIBUR DIESEL ENGINES Remanufactured Long Block (Includes Heads, Block, Rods, Pistons, Crank, Valvetrain, Oil Pump) - THESE ARE THE HIGHEST QUALITY REMAN MOTORS FOR THE MONEY AND FOR WHAT ALL WE DO TO THE MOTORS THAT OTHERS DON'T! www.xcaliburdieselengines.com OUR MOTORS ARE NOT THE CHEAPEST OR ARE THEY THE MOST EXPENSIVE FOR THE SAME PRODUCT BUT WE STAND BEHIND OUR PRODUCT AND WHAT WE BUILD AND SELL, WE PRICE ACCORDINGLY TO PRODUCTS USED, TYPE OF PRODUCTS AND SERVICES PERFORMED ON OUR REBUILDS, COMPARE PART TO PART AND WORK PERFORMED BEFORE YOU THINK WE ARE MORE EXPENSIVE THAN OTHERS! 3 YEAR / 100,000 Mile Workmanship Warranty (STANDARD WARRANTY for MOST Rebuilders) (PARTS ONLY/NO LABOR) - Must follow warranty instructions for warranty to be active. Shipping price of a Flat Rate of $450 includes shipping insurance to cover the motor incase of lost or damaged items and must go to a business with forklift, residential and/or liftgate required adds $150 to the shipping cost. LB7 PISTONS USED IN OUR BUILDS EARLY AND LATE TO HELP WITH KNOWN PISTON CRACKING ISSUES ON LBZ/LMM/LML MOTORS!! Call to Finalize this Engine Order so we can get all necessary Information. Here are some details about what goes into one of our re-manufactured motors and sets our motors apart from the rest of the standard remans on eBay and offered by other shops. We may have a higher priced motor but look at all the upgrades we do for a long lasting dependable motor! We can do these for $7,500 direct if you contact us directly and save money if it is a out of state purchase on tax. Call to purchase over the phone or by email. Block cleaned, checked and paintedLine honed Checked and bored and honed if out of specBlock Surface is Decked for Optimum Gasket Sealing (Most shops Roloc the surface which is NOT the correct way) Bored then TORQUE PLATE FINISH HONED (no one else does this and is a must for use with ARP Head Studs) for Mahle LB7 Pistons (We can offer these in a delipped piston and coated options also)Rods reconditioned to OE SpecsNew GM main bolts (can be upgraded to ARP Main Studs)New GM rod bolts (can be upgraded to ARP Rod BoltsNew Mahle or Dualogy LB7 pistons with New RingsNew Mahle or King performance main bearingsNew Mahle or King performance rod bearingsNew Mahle or King Thrust Washer SetHeads pressure tested, valves checked, valve guides replaced with SBI guides if out of spec and then all 01-10 model heads get bronze guide liners installed for ultimate longevity and performance over just having standard cast guides for the valves to ride on, while LML heads get upgraded to the better earlier style valve guides and seals, valve seals replaced, 3-4 angle valve job performed, and surface machined and now we also install BRAND NEW valve springs on all heads as standard and can be upgraded to a HD spring also. New Mahle UPGRADED Grade C Wave Stopper head gaskets (if available can be upgrade to a Cometic MLX Head Gasket)Cam is inspected and measured and keyway machined in place of the dowel pin that is known to shear off and cause motor damage(we can also install any aftermarket cam like the Alternative Firing Order Cams to help save your Crankshaft) ARP HEAD STUDS are always used Includes New Block Heater alsoKEYED Crankshaft to prevent the Dampner from spinning on the crankshaft and ruining it and keyed for the oil pump gear / tone wheelKEYED Camshaft to prevent valve train damage when they slip on the factory dowel setup Wagler Competition High Pressure/Volume Oil Pump (these are way superior to the factory and unlike others on eBay we replace the oil pump instead of reuse) Magnafluxed and Polished CrankshaftFully assembled with final numbers to OE SpecsFully Balanced Rotating Assembly, Factory Setups are usually around 20 grams out of balance and after final balance we have them within 3 grams +/- for a smooth running engine (which most rebuilders will skip to save money)Mahle Lower Gasket Kit Included for the oil pan, front cover, and rear cover gasketsCleaned and Sandblasted Front and Rear Covers with the Upper Oil Pan and a NEW Lower Oil Pan with a New GM Oil Level Sensor, which also includes upgrading the rear seal to a GM Rear Seal and also a Billet Coolant Block Off Plate on the Rear Cover can be installed for $500 Extra to save lots of time and clean up. Message me your contact info if you want to do add ons so I can quote it correctly or check status on a motor build! I also have front covers, rear covers, oil pans, intake runners if needed also for extra that can be pre-installed so that the seals are all properly installed preventing issues if having down at your house or shop that does not have the correct tools. Send me a email for a quote. Need the head set also to finish installation which includes the rest of the gaskets for installation?? Need bigger valve springs installed? Better Pushrods? Let us know how we can help with your next motor build. We can also provide CP3 Pumps, Injectors, Turbo Kits, Coated Pistons, Carrillo Rods, Performance Built Engines, etc. CORE OF $1500 NOT INCLUDED IN THE PRICE - WE WILL EMAIL YOU A SEPERATE CORE INVOICE FOR THE CORE CHARGE TO BE PAID AND ONCE WE RECIEVE THE CORE THEY WILL BE CHECKED AND THE CORE FEE WILL BE REFUNDED PER OUR INSPECTION - 2001-2010 Duramaxs have a Refundable $1500 Core for a Rebuildable Motor, which will be refunded upon receiving and checking your long block. Broke Cranks minus $500 Core Charge, Bent Rods minus $50ea rod, Damaged Head minus $300 per head, Damaged or unusable Blocks minus $500, etc - 2011-2016 Duramax LMLs have a $2000 Core Charge due to the demand for cores as this is what we have to pay for them. Let us know if you have any questions. If you want to purchase please check with us on lead time before shipping, we try to keep one built at all times but depends on orders received, we always have engines in line getting machined so please check with us on lead time sometimes it may take 2-6 weeks once ordered if we are sold out, and if you want other parts installed this will add to build time. Thanks for looking!

Price: 8195 USD

Location: Elizabethton, Tennessee

End Time: 2024-08-04T12:50:49.000Z

Shipping Cost: 450 USD